Measurement's report MEElectronics S6 test and graphs - Reference Audio Analyzer
MEElectronics S6



Manufacturers / MEElectronics

MEElectronics S6 (report for a pro)



About this report
This is a headphone report for professionals.
You can see a simple report for "dummies" with explanations of the main characteristics for MEElectronics S6

One product can have multiple reports in different modes and with different a suite of tests.



Test report - general data of MEElectronics S6 headphone

Frequency response, Impedance, Frequency response with standard AMPs


Graphics setting view
Range, dB:

Perception of headphone frequency response curves of equal loudness ISO 226-2009


General results
General results MEElectronics S6
Channel
Center/Summary
Sensitivity average in band from 100 Hz to 10 kHz, dB/V
123,6
Impedance average in band from 40 Hz to 15 kHz, ohm
15,7
For 94,0 dB SPL need, VRMS
0,033
For 94,0 dB SPL need, mW
0,070

The table shows a most important technical characteristics of MEElectronics S6

*Center channel headphone is received by averaging between left and right channels



Test conditions
  • Type of headphones: In-Ear or Tablet
  • Measurements were performed on the stand:
    • Solid simulator-bushing SIEC (emulation of auditory channel)


The tags (specifications) for this report are:
Type of product :
Headphones tested in :
Headphones tested on :
Type of headphones :
The type of acoustic design :


To send tags for moderation

If some tags are assigned incorrectly or not all are added, select it as appropriate and send it for moderation.




Sensitivity of MEElectronics S6 headphone


Graphics setting view
Channel:


Brief information
The sensitivity of the headphones F.A.Q. is determined by the amplitude-frequency response curve F.A.Q. with the specified sound pressure dB SPL of 1 VRMS. For 0 dB, 20 μPa is assumed.

By the sensitivity of the headphones, you can predict the volume level developed by the headphones at any chosen frequency with the known supply voltage to the headphones from the amplifier. Three-wave smoothing F.A.Q. is used to eliminate the interference of waves due to the use of a "point" microphone.

The frequency response in RAA is obtained through the reproduction and analysis of a special noise signal with the subsequent generation of an impulse response. The frequency response plot is constructed from the spectrum of the impulse response.

The difference in amplitudes of 6 dB is equivalent to a twofold ratio of signal levels.

Original text in Russian report. You can help with translation via the forum or feedback.


Table
Sensitivity MEElectronics S6
Channel
Left
Right
Sensitivity average in band from 100 Hz to 10 kHz, dB/V
122,9
124,2
Sensitivity at 500 Hz at 1 V, dB
120,0
121,6
Sensitivity at 500 Hz at 1 mW, dB
102,0
103,6
Sensitivity at 1000 Hz at 1 V, dB
118,0
119,3
Sensitivity at 1000 Hz at 1 mW, dB
100,0
101,2

The sensitivity was calculated by data from the measuring stand SIEC



Comparison of the parameters by on-line services

Compare the frequency response of headphones with sensitivity

How much sensitivity of the MEElectronics S6 different from other models?
Comparison the frequency response with sensitivity graph of MEElectronics S6 on-line.

Comparison of change of SPL and frequency response of headphones depending on the applied voltage level and the impedance of the audio source


Comparison of change of SPL and frequency response of MEElectronics S6 depending on the applied voltage level and the impedance of the audio source by on-line service.

Comparison of the sensitivity value MEElectronics S6 versus other models

How much are the characteristics of MEElectronics S6 different from other models?
This can be compared for all measured headphone models

Determination of the required voltage level from the headphone amplifier and comparison with other models

What voltage range from the amplifier is needed for the MEElectronics S6?
Comparison of on-line graphs with additional analytics of compatibility with specific amplifiers. In comparison, the required voltage value, which the amplifier should provide for the selected sound pressure, is determined based on the sensitivity value of the MEElectronics S6.

Frequency response of MEElectronics S6 headphone


Graphics setting view
Range, dB:
Channel:


Brief information
Graph of frequency response F.A.Q. the shows the balance of the frequency of the headphones (reproduced frequency spectrum) in dB. 0 dB is the average of the amplitude.

The frequency response of the headphones can be represented as the selected equalizer setting in the player, applicable to headphones with a flat sound. Subjective "flatness" is perceived differently from external conditions: the volume level F.A.Q. of the external noise and noise isolation headphones. When connected to an amplifier, the frequency response can change F.A.Q..

The frequency response in RAA is obtained through the reproduction and analysis of a special noise signal with the subsequent generation of an impulse response. The frequency response plot is constructed from the spectrum of the impulse response.

According to the frequency response curve, it is possible to calculate the width of the frequency range F.A.Q..

The difference in amplitudes of 6 dB is equivalent to a twofold ratio of signal levels.

Original text in Russian report. You can help with translation via the forum or feedback.


Table
Frequency response MEElectronics S6
Channel
Left
Right
Variation in frequency response in band from 100 Hz to 10 kHz, dB
-4,97, 8,29
-4,95, 7,81


The RMS variation between the right and left channels
MEElectronics S6 from stand SIEF
Deviation between channels in band 40 Hz to 15 kHz, dB
0,5
Deviation between channels in low-frequency range 40 Hz to 200Гц, дБ
0,7
Deviation between channels in mid-frequency range 200 Hz to 2 kHz, dB
0,2
Deviation between channels in hi-frequency range 2 kHz 15 kHz, dB
0,4


Comparison of the parameters by on-line services

Comparison the frequency response of MEElectronics S6 versus other models

How much frequency response of the MEElectronics S6 different from other models?
Comparison the frequency response of


Impedance of MEElectronics S6 headphone


Graphics setting view
Channel:


Brief information
Impedance indicates the resistance of the earphone, depending on the frequency.

The vertical scale of resistance is presented on a logarithmic scale.

The impedance of the headphones affects the current consumption from the amplifier, changes in frequency response when connected to an amplifier F.A.Q. and indirectly on the sensitivity of the headphones F.A.Q. to the voltage.

Original text in Russian report. You can help with translation via the forum or feedback.


Table
Impedance MEElectronics S6
Channel
Left
Right
Impedance average in band from 40 Hz to 15 kHz, ohm
15,7
15,8
Resistance at 500 Hz, ohm
15,7
15,7
Resistance at 1000 Hz, ohm
15,7
15,7
The minimum value in band from 40 Hz to 15 kHz at frequency, Hz
42,6
40,6
The minimum value in band from 40 Hz to 15 kHz, ohm
15,7
15,7
The maximum value in band from 40 Hz to 15 kHz at frequency, Hz
5208,1
5208,1
The maximum value in band from 40 Hz to 15 kHz, ohm
16,5
16,7


Comparison of the parameters by on-line services

Comparison of the impedance of MEElectronics S6 versus other models

How much are the characteristics of MEElectronics S6 different from other models?
This can be compared for all measured headphone models


Electric phase of MEElectronics S6 headphone


Graphics setting view
Range, degree:
Channel:


Brief information
The electrical phase determines the "lightness of the load" for the amplifier.

Original text in Russian report. You can help with translation via the forum or feedback.


Table
Electric phase MEElectronics S6
Channel
Left
Right
Average variation in phase response in band from 20 Hz to 20 kHz, degree
0,9
0,9
The minimum value in band from 20 Hz to 20 kHz at frequency, Hz
5464,5
5464,5
The minimum value in band from 20 Hz to 20 kHz, degree
0,0
-0,4
The maximum value in band from 20 Hz to 20 kHz at frequency, Hz
19682,2
19682,2
The maximum value in band from 20 Hz to 20 kHz, degree
5,8
5,8

Frequency response of MEElectronics S6 headphone when connected to amplifiers with constant output impedance


Graphics setting view
Range, dB:
Channel:


Brief information
The test shows the frequency response of the headphones when connected to amplifiersF.A.Q., whose output impedance is constantly operating frequency range.



For the analysis, the choice of amplifiers with resistances: 10, 20, 50, 100 and 300 Ohms.

Original text in Russian report. You can help with translation via the forum or feedback.


Table
Frequency response of headphone MEElectronics S6 with amplifier with a constant impedance
Channel
Left
Right
Variation in FR from AMP 0 ohm in band 100 Hz to 10 kHz, dB
-4,97, +8,29
-4,95, +7,81
Variation in FR from AMP 10 ohm in band 100 Hz to 10 kHz, dB
-4,98, +8,41
-4,96, +7,97
Variation in FR from AMP 20 ohm in band 100 Hz to 10 kHz, dB
-4,98, +8,47
-4,97, +8,05
Variation in FR from AMP 50 ohm in band 100 Hz to 10 kHz, dB
-4,98, +8,55
-4,97, +8,14
Variation in FR from AMP 100 ohm in band 100 Hz to 10 kHz, dB
-4,99, +8,59
-4,97, +8,19
Variation in FR from AMP 300 ohm in band 100 Hz to 10 kHz, dB
-4,99, +8,62
-4,98, +8,23


Comparison of the parameters by on-line services

Compare the frequency response of a bundle of headphones and amplifiers

How much frequency response of the MEElectronics S6 changes when connected to different amplifiers? In the example the MEElectronics S6 and AMPs Apple iPhone 5S, Xiaomi Redmi Note 4X PowerAmp, Astell&Kern KANN Balance, Oriolus DP100 Unbalance, Shanling M3s Unbalance . You can choose and compare bundles with other amplifiers.

Deviation of frequency response of MEElectronics S6 headphone when connected to amplifiers with constant output impedance


Graphics setting view
Range, dB:
Channel:


Brief information
The test shows only the change frequency response headphones F.A.Q. when connected to amplifiers, whose output impedance is constant in the operating frequency range.

At the amplifier the impedance can be of different sizes and when agreed with the impedance of the headphones, change in the frequency response F.A.Q. to varying degrees. The lower the output impedance of the amplifier and the higher the resistance of the headphones, the smaller the change.

Original text in Russian report. You can help with translation via the forum or feedback.


Table
Variation in frequency response with amplifiers with constant output resistance from MEElectronics S6
Channel
Center/Summary
With amplifier impedance at 10 ohm in band 20 Hz to 20 kHz, dB
0,2
With amplifier impedance at 20 ohm in band 20 Hz to 20 kHz, dB
0,3
With amplifier impedance at 50 ohm in band 20 Hz to 20 kHz, dB
0,4
With amplifier impedance at 100 ohm in band 20 Hz to 20 kHz, dB
0,4
With amplifier impedance at 300 ohm in band 20 Hz to 20 kHz, dB
0,4

*Center channel is received by data averaging between the left and right channels



Comparison of the parameters by on-line services

Compare the frequency response of a bundle of headphones and amplifiers

How much frequency response of the MEElectronics S6 changes when connected to different amplifiers? In the example the MEElectronics S6 and AMPs Apple iPhone 5S, Xiaomi Redmi Note 4X PowerAmp, Astell&Kern KANN Balance, Oriolus DP100 Unbalance, Shanling M3s Unbalance . You can choose and compare bundles with other amplifiers.

Frequency response of MEElectronics S6 headphone when connected to an amplifier with zero output impedance and raising of output impedanse in low frequencies


Graphics setting view
Range, dB:
Channel:


Brief information
The test shows the frequency response of the headphones when connected to amplifiersF.A.Q., whose output impedance is close to zero in the mid and high frequency range, but increases in the low frequency range.



An amplifier of this type was chosen for the analysis.

Original text in Russian report. You can help with translation via the forum or feedback.


Table
Frequency response with an amplifier with zero output resistance and raising of output resistance in low frequencies from MEElectronics S6
Channel
Left
Right
Variation in frequency response in band from 100 Hz to 10 kHz, dB
-4,82, 8,46
-4,81, 7,98


Comparison of the parameters by on-line services

Compare the frequency response of a bundle of headphones and amplifiers

How much frequency response of the MEElectronics S6 changes when connected to different amplifiers? In the example the MEElectronics S6 and AMPs Inakustik Premium Headphone Amp. No. 1 Out 2, Fly FS504 Cirrus 2 PowerAmp (A5 v703), Hidizs AP100, iBasso D-Zero, iBasso D10 Cobra, Cowon C2, Colorful Colorfly CK4, Colorful Colorfly C4 Pro Jack 3.5, Benjie X1, Lotoo PAW Pico . You can choose and compare bundles with other amplifiers.

Deviation of frequency response of MEElectronics S6 headphone when connected to an amplifier with zero output impedance and raising of output impedanse in low frequencies


Graphics setting view
Range, dB:
Channel:


Brief information
The test shows only the change frequency response headphones F.A.Q. when connected to amplifiers, whose output impedance is constant in the operating frequency range.

The lower the impedance of headphones in the low-frequency range, the stronger the low frequencies are weakened. With high-impedance headphones, there is no noticeable change in the frequency response F.A.Q.. Original text in Russian report. You can help with translation via the forum or feedback.


Table
Variance of frequency response MEElectronics S6 depending on the total output resistance of the amplifier with zero resistance and a rise of resistance at low frequencies
Variance frequency response at the frequency 20 Hz, dB
-8,4
Variance frequency response at the frequency 40 Hz, dB
-3,9
Variance frequency response at the frequency 80 Hz, dB
-1,6


Comparison of the parameters by on-line services

Compare the frequency response of a bundle of headphones and amplifiers

How much frequency response of the MEElectronics S6 changes when connected to different amplifiers? In the example the MEElectronics S6 and AMPs Inakustik Premium Headphone Amp. No. 1 Out 2, Fly FS504 Cirrus 2 PowerAmp (A5 v703), Hidizs AP100, iBasso D-Zero, iBasso D10 Cobra, Cowon C2, Colorful Colorfly CK4, Colorful Colorfly C4 Pro Jack 3.5, Benjie X1, Lotoo PAW Pico . You can choose and compare bundles with other amplifiers.

Perception of headphone frequency response curves of equal loudness ISO 226-2009 of MEElectronics S6 headphone


Graphics setting view
Channel:


Brief information
Brief information
The graph shows the change in the perception of the frequency responseF.A.Q. of the headphones when listening to music with a different loudness relative to the natural level. When listening to headphones at a low volume, the perception of recoil in the low frequency range decreases, and when you listen to it at a high volume, it increases.

According to this graph, you can estimate at what volume the headphones will be perceived more flat.

The perception of the number of low frequencies depends on the volume according to the curves of equal loudness. (ISO 226-2009 Acoustics. Normal equal-loudness-level contours). For the base level, 72 dB SPL (live performance of several instruments with vocals without amplifiers with acoustics) is selected.When you select another base level, the dependence varies slightly and is suitable for almost all levels.

Examples of graphics application in practice F.A.Q..

Original text in Russian report. You can help with translation via the forum or feedback.


Table
Perception of headphone frequency response curves of equal loudness ISO 226-2009 from MEElectronics S6
Channel
Center/Summary
From level 48 dB at 72 dB SPL in band 100 Hz to 10 kHz, dB
-8,6, +17,8
From level 36 dB at 72 dB SPL in band 100 Hz to 10 kHz, dB
-7,7, +14,7
From level 24 dB at 72 dB SPL in band 100 Hz to 10 kHz, dB
-6,8, +11,6
From level 12 dB at 72 dB SPL in band 100 Hz to 10 kHz, dB
-5,8, +8,6
From level 0 dB at 72 dB SPL in band 100 Hz to 10 kHz, dB
-5,0, +8,0
From level -12 dB at 72 dB SPL in band 100 Hz to 10 kHz, dB
-4,2, +9,1
From level -24 dB at 72 dB SPL in band 100 Hz to 10 kHz, dB
-3,6, +10,3
From level -36 dB at 72 dB SPL in band 100 Hz to 10 kHz, dB
-3,2, +11,3

*Center channel is received by data averaging between the left and right channels



On-line comparison and selection services for MEElectronics S6

Comparison the frequency response the MEElectronics S6 versus other models

Compare the sensitivity and impedance the MEElectronics S6 versus other models.

The automatic selection of the optimal AMP models from MEElectronics S6 from the measured power parameters of the amplifying part and the measured parameters of the headphones for different purpose of use.

Сравнение АЧХ и звукового давления MEElectronics S6 в зависимости от подаваемого напряжения и импеданса усилителя.

Last news


Original text in Russian page. Translation page is not yet ready

You can help with translation via the:


Share report

If you notice a typo or other inaccuracy, then select it and press Ctrl+Enter. This will accelerate the process of improving the reports.

The original language of the report in Russian. If the text in the report is unclear, use online translators Russian-language report (and help with the correct translation into English)

Glossary: RUS, ENG. To display on page ID need to enable debug mode.

Debug mode: Switch ON

Follow