Measurement's report Auzentech Auzen X-Fi Bravura 7.1 test and graphs - Reference Audio Analyzer

Reports / Auzentech / Auzen X-Fi Bravura 7.1 / A set of device tests as a headphone amplifier - report for a pro

Test report Auzentech Auzen X-Fi Bravura 7.1 (report for a pro)






Test report - general data of Auzentech Auzen X-Fi Bravura 7.1 as AMP mode

Frequency response, Impedance and Frequency response with standard headphones


Graphics setting view
Range, dB:


General results
General results
Auzentech Auzen X-Fi Bravura 7.1
Channel
Left
Average variation in FR in the band 40 Hz to 15 kHz, dB
-1,17, 0,08
Average value of impedance band in 40 Hz to 15 kHz, ohm
12,0
Max voltage output
VRMS
dBV
Maximum current output at loaded
ohm
mA
Max power output
ohm
mW
dBm

The table shows a most important technical characteristics of Auzentech Auzen X-Fi Bravura 7.1



Test conditions
  • For record of test signals RAA was used ADC: E-MU 1616m
  • During tests RAA software-hardware measuring complex was used galvanic isolated power transformer and was excluded the effect of ground loop in the spectra



Frequency response of Auzentech Auzen X-Fi Bravura 7.1 as AMP mode


Graphics setting view
Range, dB:




Table of measured characteristics
Frequency response Auzentech Auzen X-Fi Bravura 7.1
Channel
Left
Variation in frequency response in band from 100 Hz to 10 kHz, dB
-0,21, 0,04

Impedance of Auzentech Auzen X-Fi Bravura 7.1 as AMP mode





Table of measured characteristics
Impedance Auzentech Auzen X-Fi Bravura 7.1
Channel
Left
Impedance average in band from 40 Hz to 15 kHz, ohm
12,0
Resistance at 500 Hz, ohm
12,0
Resistance at 1000 Hz, ohm
12,0
The minimum value in band from 40 Hz to 15 kHz at frequency, Hz
53,0
The minimum value in band from 40 Hz to 15 kHz, ohm
11,8
The maximum value in band from 40 Hz to 15 kHz at frequency, Hz
40,8
The maximum value in band from 40 Hz to 15 kHz, ohm
12,1

Frequency response of Auzentech Auzen X-Fi Bravura 7.1 with loaded resistors as AMP mode


Graphics setting view
Range, dB:




Table of measured characteristics
Frequency response of amplifier headphone amplifier Auzentech Auzen X-Fi Bravura 7.1
with resistive load
Channel
Left
Variation in frequency response in band 40 Hz to 15 kHz loaded 16 ohm, dB
0,08
Variation in frequency response in band 40 Hz to 15 kHz loaded 32 ohm, dB
0,05
Variation in frequency response in band 40 Hz to 15 kHz loaded 50 ohm, dB
0,03
Variation in frequency response in band 40 Hz to 15 kHz loaded 100 ohm, dB
0,02
Variation in frequency response in band 40 Hz to 15 kHz loaded 250 ohm, dB
0,01
Variation in frequency response in band 40 Hz to 15 kHz loaded 600 ohm, dB
0,00

Frequency response of Auzentech Auzen X-Fi Bravura 7.1 loaded dynamic headphone type as AMP mode


Graphics setting view
Range, dB:




Table of measured characteristics
Frequency response of the headphone amplifier Auzentech Auzen X-Fi Bravura 7.1
loaded dynamic headphone type
Channel
Left
Variation in frequency response in band 40 Hz to 15 kHz load the dynamic type, dB
1,98

Deviation of frequency response of Auzentech Auzen X-Fi Bravura 7.1 loaded dynamic headphone type as AMP mode


Graphics setting view
Range, dB:




Table of measured characteristics
Frequency response of amplifier Auzentech Auzen X-Fi Bravura 7.1
loaded dynamic headphone type
Channel
Left
Variation in frequency response in band 40 Hz to 15 kHz load the dynamic type, dB
1,14

Frequency response of Auzentech Auzen X-Fi Bravura 7.1 loaded type balance armature headphone type (one driver) as AMP mode


Graphics setting view
Range, dB:




Table of measured characteristics
Frequency response of amplifier Auzentech Auzen X-Fi Bravura 7.1
loaded type balanced armature
Channel
Left
Variation in frequency response in band 40 Hz to 15 kHz loaded type balanced armature, dB
3,73

Deviation of frequency response of Auzentech Auzen X-Fi Bravura 7.1 loaded type balance armature headphone type (one driver) as AMP mode


Graphics setting view
Range, dB:




Table of measured characteristics
Frequency response of amplifier Auzentech Auzen X-Fi Bravura 7.1
loaded type balanced armature
Channel
Left
Variation in frequency response in band 40 Hz to 15 kHz loaded type balanced armature, dB
4,22



Close

Measurements of Auzentech Auzen X-Fi Bravura 7.1 were carried out by Roman Kuznetsov on the hardware-software complex RAA.

The Auzentech Auzen X-Fi Bravura 7.1 test was conducted as a black box test, without regard to cost and prestige. This is the basic principle for making measurements, measurement reports and developing tests in RAA.

I believe that it is important to do not make an absolute assessment of the device, but an aggregate assessment when working together with a headphones and taking into account external factors. This allows you to effectively reveal the potential of the entire set of devices or to make a more optimal choice of components.




Kuznetsov Roman
Founder of RAA



Known by the nickname romanrex
Аuthor of articles iXBT.com



Information for Authors. You can freely use the graphics in your articles with a link to us.



Auzentech Auzen X-Fi Bravura 7.1 is available in reports and services. You are in a professional report.

Information for entry level users





Original text in Russian page. Translation page is not yet ready

You can help with translation via the: forum, facebook and feedback.

 

Comments

No comments to Auzentech Auzen X-Fi Bravura 7.1
Commentary view:





Want to leave a comment or ask a question? Register now or log in